GMS OCC system features dual, filtered, drainable, oil catch can setup for maximal efficiency. All the parts are aluminum CNC'd and incognito black anodized and the entire assemlby is prebuilt for plug and play installation. The only, plug and play solution on the market, to keep your 4C engine clean of carbon build-up and potential reliability issues.
Oil catch cans are simple devices that can greatly benefit especially DFI (direct fuel injection engines). They prevent oil and other contaminants from causing carbon build-up inside your engine and prevent oily and greasy engine bay area. Clean air intake has also reduced chance of engine knocking, commonly an issue on tuned engines with excessive oil vapors in the intake. With GMS OCC system, all this issues are solved.
Here is how the OCC works, and why you might care to install one in your own car. Alfa Romeo 4C's 1.75 Tbi engine is a DFI and has dual PCV (positive crankcase ventilation) system that allows the breathing of the crankcase. While the engine is rotating, a pressure is generated within the crankcase. This pressure has to be relieved, otherwise the pressure would build up and push the oil out of the engine, either through the oil pan, oil dipstick or any other path it could find. PCV does that by circulating the air within the engine. The PCV collects the oily fumes and vapors circulating within the engine crankcase and separates the oil from air and then returns the partially cleaned air (oil, unburnt gas) back to the intake path where this air, then mixes with fresh air and it goes through the combustion process, once again. This provides maintenance free and emission friendly system. All good, so what is the bad part?
Recirculated and partially cleaned air (oil, water, unburnt fuel) enters in two locations. One is right before the turbo compressor and the second is right after the intake throttle body. The bad thing is, that this partially cleaned air is messing up your entire engine internals, as the intake system is getting oily. That is why you find oil in charge pipe, intercooler, intake, throttle body, etc. Excessive oil in the intake system, significantly increases the chance of knocking due to lowered octane rating, caused by air being contaminated with oil and after time, also the engine bay will get greasy as well. Not good and not nice either.
The second and even more common issue which is especially a concern on DFI engines, is a carbon build-up on the valves. Why? The oily air from the intake, travels through intake valves and exits through the exhaust valves. The exhaust valves are very hot, so most of the oily air burns, but the intake valves are not so hot and so this oily air turns into carbon deposits and sits on the valves and inlet ports of the head, contaminating your valving area with carbon build-up. Older, non DFI engines, injected gasoline before the intake valves, which greatly helped to keep the valves clean, but DFI engines inject gasoline directly into the cylinder, so the valves can not get cleaned by the gasoline and therefore are far more prone to the carbon build-up. Depending of your driving style and the engine oil you are using, your 4C engine starts to build-up carbon deposits, from the day one you turn on the engine. You slowly start losing engine performance as the carbon build-up takes the volume and head flow starts to decrease. In worst case scenario your valving gets filled up with carbon deposits to the point, that the valves cannot operate properly anymore, causing engine issues. There is also a chance, that a chunk of carbon build-up tears off and drops in to the cylinder, jamming piston rings messing up the engine internals, leading to an complete engine failure.
Having a quality GMS OCC system installed on your DFI engine, the issues mentioned above are not a concern anymore.
Highly recommended reliability upgrade for street, track and race driven 4C's.
ALFA ROMEO - 4C - OCC System (oil catch can)
- Aluminum T6-6061, billet, CNC, dual 300ml, OCC tanks (enough capacity for heavy tracking)
- Smart filtering system (baffled, height split and filtered)
- Dip stick for checking the OCC oil level
- Twist & drain system for quick draining of the OCC
- Drain port on the bottom of the OCC for optional bottom oil draining
- All aluminum T6-6061 CNC construction
- AN, full flow, aluminum, pushlock fittings
- Fully serviceable (washable and replaceable mesh filter)
- Incognito black anodized
- Laser engraved logo
- Plug and play
- Weight 1430g
- Fits all Alfa Romeo 4C Coupe or Alfa Romeo 4C Spider